If you have been reading about retention time and want a single page that covers the useful parts, this is it: definitions, context, how it is studied, and the questions that come up repeatedly.
Updated 2026-08-01. Numbers and descriptions here follow the published literature rather than marketing material.
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
| Property | Value | Notes |
|---|---|---|
| Validation parameter | Accuracy | Closeness to a reference value. |
| Validation parameter | Precision | Repeatability or intermediate precision. |
| Validation parameter | Linearity | Proportional response across a range. |
| System suitability check | Resolution | Separation between adjacent peaks. |
| Quality control tool | Control chart | Tracks results over time for trends. |
Several separation modes exist, including reversed-phase, normal-phase, ion-exchange, size-exclusion, and hydrophilic interaction liquid chromatography. Reversed-phase uses a nonpolar stationary phase with a polar mobile phase and is widely applied to small organic molecules. Gradient elution changes mobile phase composition during the run, while isocratic elution keeps it constant. Column chemistry, particle size, temperature, flow rate, and mobile phase pH all influence retention and resolution. Method development selects conditions that separate analytes from matrix components and from each other.
Detection commonly uses ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. Ultraviolet detection depends on molecular chromophores that absorb light at specific wavelengths. Mass spectrometry provides mass information and sensitive quantification, often after electrospray ionization. Before sample batches, performance checks examine resolution, elution time repeatability, peak symmetry, and plate count. Matrix effects and co-elution remain recognized uncertainties; formal validation studies and orthogonal detection help address them. Detector choice depends on analyte properties and required sensitivity.
High-performance liquid chromatography, or HPLC, separates dissolved compounds by passing a liquid mobile phase through a packed column. Components distribute differently between the stationary phase and the moving liquid, so they travel at different speeds and exit at different times. A detector records these eluting bands as peaks, and peak area or height relates to amount. The technique supports testing in pharmaceuticals, foods, environmental samples, and industrial chemicals. Quantification usually depends on calibration with known standards.
In quality control laboratories, HPLC testing supports batch release, raw material checks, stability studies, and impurity profiling. A validated method defines sample preparation, instrument settings, calibration, and acceptance criteria. Analysts compare results with specifications and investigate out-of-specification outcomes before a batch is approved. Documentation includes chromatograms, integration records, audit trails, and reagent details. Because results influence product decisions, laboratories follow formal quality systems and data integrity rules. The exact tests and limits depend on the material, its intended use, and the applicable regulatory framework.
Method validation examines whether an HPLC procedure is suitable for its intended purpose. Common parameters include accuracy, precision, specificity, linearity, range, detection limit, quantification limit, and robustness. Accuracy describes closeness to a true or accepted value, while precision describes agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from related substances. Robustness tests small deliberate changes in flow, temperature, or solvent composition. Validation is not a one-time event; methods may need partial revalidation after changes to instruments, columns, sample handling, or specification limits. Regulatory guidance provides frameworks, but some details remain method-specific.
Method validation evaluates accuracy, precision, specificity, linearity, range, detection limit, quantitation limit, and robustness. Regulatory guidance for pharmaceuticals, foods, and environmental testing defines expected documentation and acceptance criteria. Verification confirms that a validated method works in a specific laboratory with its own instruments and reagents. Calibration curves use reference standards with known purity and traceability, while measurement uncertainty is estimated from validation data, control charts, and collaborative studies. The scope of validation depends on the method's intended use.
Routine quality control monitors retention time shifts, baseline noise, system pressure, and peak shape. Trends can reveal column aging, mobile phase preparation errors, detector drift, or sample degradation. Corrective actions may include replacing the column, preparing fresh mobile phase, or recalibrating the detector. Stability testing often uses HPLC to measure parent compound loss and degradation product formation. Open questions remain about how accelerated stability results extrapolate to long-term storage under varied conditions.
Quality control for HPLC testing combines scheduled checks, documented procedures, and review of results. Before sample analysis, system suitability testing confirms that the instrument, column, and method meet predefined criteria. Common criteria include resolution between critical peaks, retention time precision, peak tailing, and theoretical plate count. Failure triggers investigation before results are reported. Records link raw data, calculations, instrument logs, and analyst identity to each batch, supporting audits and repeat analysis.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. UV detection is widely used because many organic compounds absorb light, but it requires a chromophore. Mass spectrometry provides mass-based identification and high sensitivity for trace analytes. Each detector has trade-offs in selectivity, cost, and compatibility with mobile phases. Quantification typically uses calibration curves prepared from reference standards. Results are reported as concentration, purity, or presence above a limit.
HPLC testing separates dissolved compounds by passing a liquid sample through a column packed with stationary phase. A pump delivers mobile phase at controlled flow, and the sample components interact differently with stationary and mobile phases. Compounds that spend more time in mobile phase elute earlier; those retained by stationary phase elute later. Detectors record elution as peaks, and peak area or height relates to amount. This mechanism underpins quantitative analysis of mixtures.
Most routine HPLC testing uses reversed-phase columns, where the stationary phase is nonpolar and the mobile phase is a polar mixture such as water with an organic solvent. Analytes partition between the two phases according to polarity, size, and charge. Gradients that change solvent composition over time can separate compounds with broad retention ranges. Isocratic conditions keep solvent composition constant and suit simpler mixtures. The choice of column chemistry, pH, and temperature affects selectivity and peak shape.
== Reporting of yields == In their 2010 Synlett article, Martina Wernerova and organic chemist, Tomáš Hudlický, raised concerns about inaccurate reporting of yields, and offered solutions—including the proper characterization of compounds. After performing careful control experiments, Wernerova and Hudlický said that each physical manipulation (including extraction/washing, drying over desiccant, filtration, and column chromatography) results in a loss of yield of about 2%. Thus, isolated yields measured after standard aqueous workup and chromatographic purification should seldom exceed 94%. They called this phenomenon "yield inflation" and said that yield inflation had gradually crept upward in recent decades in chemistry literature. They attributed yield inflation to careless measurement of yield on reactions conducted on small scale, wishful thinking and a desire to report higher numbers for publication purposes.
=== Related species === Cod forms part of the common name of many other fish no longer classified in the genus Gadus. Many are members of the family Gadidae; others are members of three related families within the order Gadiformes whose names include the word "cod": the morid cods, Moridae (100 or so species); the eel cods, Muraenolepididae (four species); and the Eucla cod, Euclichthyidae (one species). The tadpole cod family (Ranicipitidae) has now been placed in Gadidae.
=== Other wins (11) === 1955 Egyptian Matchplay 1965 World Series of Golf, NTL Challenge Cup (Canada), World Cup of Golf, World Cup of Golf Individual Trophy 1968 World Series of Golf 1972 World Series of Golf 1977 World Cup of Golf Individual Trophy 1979 PGA Grand Slam of Golf (shared title with Andy North) 1983 Skins Game 1986 Fred Meyer Challenge (with Greg Norman - team shared title with Peter Jacobsen and Curtis Strange)
== Activity == Given its half-life, the radioactive activity of a gram of 60Co is close to 42 TBq (1,100 Ci). The absorbed dose constant, used in calculations of gamma-ray exposure, is related to the decay energy and time. For 60Co it is equal to 0.35 mSv/(GBq h) at one meter from the source. This allows calculation of the equivalent dose, which depends on distance and activity - for example, 2.8 GBq or 60 μg of 60Co, generates a dose of 1 mSv at 1 meter away, within an hour. Test sources, such as those used for school experiments, have an activity of <100 kBq. Devices for nondestructive material testing use sources with activities of 1 TBq and more. The decay energy of cobalt-60 amounts to about 26 watts per gram, about 40 times larger (by mass) than that of e.g. 238Pu but still not very significant for practical sources.
cGMP is produced slowly and has a more sustained life than cAMP, which has implicated it in long-term cellular responses to odor stimulation, such as long-term potentiation. cGMP in the olfactory is synthesized by both membrane guanylyl cyclase (mGC) as well as soluble guanylyl cyclase (sGC). Studies have found that cGMP synthesis in the olfactory is due to sGC activation by nitric oxide, a neurotransmitter. cGMP also requires increased intracellular levels of cAMP and the link between the two second messengers appears to be due to rising intracellular calcium levels.
Sources: en.wikipedia.org
== Synthesis == The compound is obtained by the thermal disassociation of KBF4·4SO3 or via reaction of potassium tetrafluoroborate (KBF4) with sulfur trioxide (SO3) at 70 °C. Also, trisulfuryl fluoride is formed in a reaction of sulfur trioxide (SO3), boron trifluoride (BF3), and 70% sulfuric acid (H2SO4) at 70 °C.
The arachnoid mater, or arachnoid membrane, is the middle element of the meninges. Thin and transparent, its name reflects its resemblance to a spider web. Its fibrous tissue cushions the central nervous system. Like the pia mater, it has an outer layer of tightly packed flat cells, forming the arachnoid barrier. The arachnoid is loosely fitting and does not closely follow the ridges and grooves on the surface of the brain. A large number of fine filaments called arachnoid trabeculae pass from the arachnoid through the subarachnoid space to blend with the tissue of the pia mater. The arachnoid barrier creates a restrictive permeability barrier between the cerebrospinal fluid in the subarachnoid space and the blood circulation in the dura. The arachnoid barrier layer is characterized by a distinct continuous basal lamina on its inner surface toward the innermost collagenous portion of the arachnoid reticular layer.
== Adverse effects == The exact incidence of the adverse effects of dexamethasone is not available, hence estimates have been made as to the incidence of the adverse effects below based on the adverse effects of related corticosteroids and on available documentation on dexamethasone.
=== Aspartate === The biosynthesis of aspartate frequently involves the transamination of oxaloacetate. The enzyme aspartokinase, which catalyzes the phosphorylation of aspartate and initiates its conversion into other amino acids, can be broken up into 3 isozymes, AK-I, II and III. AK-I is feed-back inhibited by threonine, while AK-II and III are inhibited by lysine. As a sidenote, AK-III catalyzes the phosphorylation of aspartic acid that is the committed step in this biosynthetic pathway. Aspartate kinase becomes downregulated by the presence of threonine or lysine.
Sources: en.wikipedia.org
These included the explosion of Air India Flight 182 in 1985, the largest mass murder in Canadian history; the École Polytechnique massacre in 1989, a university shooting targeting female students; and the Oka Crisis of 1990, the first of a number of violent confrontations between provincial governments and Indigenous groups. Canada joined the Gulf War in 1990 and was active in several peacekeeping missions in the 1990s, including operations in the Balkans during and after the Yugoslav Wars, and in Somalia, resulting in an incident that has been described as "the darkest era in the history of the Canadian military". After the September 11 attacks in the United States, Canada sent troops to Afghanistan in 2001, resulting in the largest amount of Canadian deaths for any single military mission since the Korean War in the early 1950s. In 2011, Canadian forces participated in the NATO-led intervention into the Libyan Civil War and also became involved in battling the Islamic State insurgency in Iraq in the mid-2010s. The COVID-19 pandemic in Canada began on January 27, 2020, causing widespread social and economic disruption. A trade war involving the United States began on February 1, 2025, when U.S. president Donald Trump signed orders imposing tariffs on goods entering the United States, alongside rhetoric suggesting the annexation of Canada.
inhalation: all intoxicative inhalants (see below) that are gases or solvent vapours that are inhaled through the trachea, as the name suggests insufflation: also known as "snorting", or "sniffing", this method involves the user placing a powder in the nostrils and breathing in through the nose, so that the drug is absorbed by the mucous membranes. Drugs that are "snorted", or "sniffed", include powdered amphetamines, cocaine, heroin, ketamine, MDMA, and snuff tobacco. Subcutaneous injection (see also the article Skin popping): injection of drug into the third lowest layer of skin. Intramuscular injection: injection of drug into a muscle. intravenous injection (see also the article Drug injection): the user injects a solution of water and the drug into a vein, or less commonly, into the tissue. Drugs that are injected include morphine and heroin, less commonly other opioids. Stimulants like cocaine or methamphetamine may also be injected. In rare cases, users inject other drugs. oral intake: caffeine, ethanol, cannabis edibles, psilocybin mushrooms, coca tea, poppy tea, laudanum, GHB, ecstasy pills with MDMA or various other substances (mainly stimulants and psychedelics), prescription and over-the-counter drugs (ADHD and narcolepsy medications, benzodiazepines, anxiolytics, sedatives, cough suppressants, morphine, codeine, opioids and others) sublingual: substances diffuse into the blood through tissues under the tongue.
==== Raman spectroscopy ==== Raman spectroscopy is one of the easiest methods to integrate into a heterogeneous operando experiment, as these reactions typically occur in the gas phase, so there is very low litter interference and good data can be obtained for the species on the catalytic surface. In order to use Raman, all that is required is to insert a small probe containing two optical fibers for excitation and detection. Pressure and heat complications are essentially negligible, due to the nature of the probe. Operando confocal Raman micro-spectroscopy has been applied to the study of fuel cell catalytic layers with flowing reactant streams and controlled temperature.
Sources: en.wikipedia.org
Method validation is the documented process of showing that an HPLC procedure produces reliable results for a defined purpose. It examines parameters such as accuracy, precision, specificity, linearity, and robustness. Regulators and quality systems often require validation before routine use.
System suitability is a set of checks run on the chromatographic system before sample analysis. It confirms that resolution, peak shape, retention time, and response meet predefined limits. Failure can invalidate the run and trigger corrective action.
Blank injections reveal peaks or baseline disturbances that come from solvents, reagents, or the instrument rather than the sample. They help distinguish contamination from actual analyte signals. Comparing blanks with sample runs supports accurate interpretation.
HPLC testing measures the presence and amount of one or more compounds in a liquid sample. It separates mixture components and records detector responses as peaks, which are compared with reference standards. Results are usually reported as concentrations or relative percentages.