HPLC comes up often in conversation and rarely with the context attached. Here we lay out the basics in order, then work through the practical considerations.
Updated 2026-04-01. Numbers and descriptions here follow the published literature rather than marketing material.
Validation establishes that a method is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, robustness, and stability of standards and samples. Acceptance criteria are defined in advance, and results are documented in a validation report. Regulatory guidance for pharmaceuticals, foods, and environmental testing differs, so the applicable framework must be identified. Ongoing verification uses control samples and trend charts after validation. Method transfer to another laboratory may require partial revalidation.
Routine quality control includes blanks, duplicates, spiked samples, and certified reference materials. Calibration curves are prepared with standards at several concentrations, and the detector response is checked for linearity. Carryover, column aging, mobile phase evaporation, and temperature drift can shift retention times or peak areas. Maintenance such as replacing seals, filters, and columns helps prevent failures. Records of injections, integration, and deviations support traceability. Audits may request raw data and instrument logs for each batch.
Quality control for HPLC testing combines scheduled checks, documented procedures, and review of results. Before sample analysis, system suitability testing confirms that the instrument, column, and method meet predefined criteria. Common criteria include resolution between critical peaks, retention time precision, peak tailing, and theoretical plate count. Failure triggers investigation before results are reported. Records link raw data, calculations, instrument logs, and analyst identity to each batch, supporting audits and repeat analysis.
Method validation evaluates accuracy, precision, specificity, linearity, range, detection limit, quantitation limit, and robustness. Regulatory guidance for pharmaceuticals, foods, and environmental testing defines expected documentation and acceptance criteria. Verification confirms that a validated method works in a specific laboratory with its own instruments and reagents. Calibration curves use reference standards with known purity and traceability, while measurement uncertainty is estimated from validation data, control charts, and collaborative studies. The scope of validation depends on the method's intended use.
| Property | Value | Notes |
|---|---|---|
| Accuracy | Closeness to true value | Often assessed by recovery of spiked samples |
| Precision | Agreement among repeated measurements | Often reported as relative standard deviation |
| Specificity | Ability to measure analyte without interference | Must separate analyte from impurities and matrix |
| Linearity | Proportional detector response | Evaluated across a defined concentration range |
| Robustness | Resistance to small method changes | Tests flow rate, pH, temperature, and mobile phase composition |
Reversed-phase chromatography dominates modern HPLC testing, using a nonpolar stationary phase such as chemically bonded octadecyl groups and a polar mobile phase of water mixed with organic solvent. Analytes partition between the mobile and stationary phases according to hydrophobicity. Gradient elution changes the mobile phase composition over time to separate compounds with a wide range of retention. Isocratic elution keeps the composition constant and is simpler for routine assays. Column temperature, pH, and flow rate influence selectivity, peak shape, and retention time, so these parameters are controlled during a validated method.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. A diode array detector records full spectra across a wavelength range, which helps identify co-eluting peaks. Mass spectrometry provides mass-to-charge ratios and can confirm molecular identity at low concentrations. The choice of detector depends on analyte structure, required sensitivity, and whether quantitation or identification is the goal. No single detector works for every compound, and method development often compares responses before selecting one.
High-performance liquid chromatography is an analytical technique that separates components of a liquid sample by passing it through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in interaction with the stationary phase cause analytes to migrate at different rates. Detectors record elution as peaks, and a data system converts signals into a chromatogram. The method is suited to compounds that dissolve in a liquid and are not volatile enough for gas chromatography.
HPLC testing separates dissolved compounds by passing a liquid sample through a column packed with stationary phase. A pump delivers mobile phase at controlled flow, and the sample components interact differently with stationary and mobile phases. Compounds that spend more time in mobile phase elute earlier; those retained by stationary phase elute later. Detectors record elution as peaks, and peak area or height relates to amount. This mechanism underpins quantitative analysis of mixtures.
Most routine HPLC testing uses reversed-phase columns, where the stationary phase is nonpolar and the mobile phase is a polar mixture such as water with an organic solvent. Analytes partition between the two phases according to polarity, size, and charge. Gradients that change solvent composition over time can separate compounds with broad retention ranges. Isocratic conditions keep solvent composition constant and suit simpler mixtures. The choice of column chemistry, pH, and temperature affects selectivity and peak shape.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. UV detection is widely used because many organic compounds absorb light, but it requires a chromophore. Mass spectrometry provides mass-based identification and high sensitivity for trace analytes. Each detector has trade-offs in selectivity, cost, and compatibility with mobile phases. Quantification typically uses calibration curves prepared from reference standards. Results are reported as concentration, purity, or presence above a limit.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample by passing them through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in how analytes partition between the mobile phase and the stationary phase cause them to exit the column at different times. Detection then records a signal proportional to the amount of each separated substance. The resulting chromatogram provides retention times and peak areas for identification and quantification.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
Zinc is an essential element for all known forms of life. In humans, zinc is required for the function of over 300 enzymes and 1000 transcription factors, and is stored and transferred in metallothioneins. It is the second most abundant trace metal in humans after iron. It is the only metal which appears in all enzyme classes. In proteins, zinc ions are often coordinated to the amino acid side chains of aspartic acid, glutamic acid, cysteine and histidine. The theoretical and computational description of this zinc binding in proteins (as well as that of other transition metals) is difficult. Roughly 2–4 grams of zinc are distributed throughout the human body. Most zinc is in the brain, muscle, bones, kidney, and liver, with the highest concentrations in the prostate and parts of the eye. Semen contains a particularly high amount of zinc, a key factor in prostate gland function and reproductive organ growth. Zinc homeostasis of the body is mainly controlled by the intestine. Here, ZIP4 and especially TRPM7 were linked to intestinal zinc uptake essential for postnatal survival. In humans, the biological roles of zinc are ubiquitous. It interacts with "a wide range of organic ligands", and has roles in the metabolism of RNA and DNA, signal transduction, and gene expression. It also regulates apoptosis. A review from 2015 indicated that about 10% of human proteins (~3000) bind zinc, in addition to hundreds more that transport and traffic zinc; a similar in silico study in the plant Arabidopsis thaliana found 2367 zinc-related proteins.
H-DNA motifs have been shown to stimulate homologous recombination with different mechanisms. Initial implications for the role of H-DNA in recombination came in the early 1990s when observing RecA, a bacterial DNA recombination protein composed of triple-helix DNA. RecA exhibits enzymatic activity essential for recombination. Homologous recombination involving H-DNA motifs have also been found in eukaryotes. RadA, a homologous protein to RecA, has been shown to have the same enzymatic activity in recombination as RecA. The protein has the ability to promote and exchange homologous strands through parallel triple stranded helices. The single stranded DNA (ssDNA) and complementary double stranded DNA (dsDNA) will form a D-loop structure. Another possible mechanism for RecA involves the ssDNA from two separate H-DNA structures to form Watson-Crick base pairs. The new structure is known as a Holliday junction, an intermediate in homologous recombination. H-DNA is also found in other forms of recombination. In mammalian cells, H-DNA-sequences displayed a high frequency of recombination. For example, a study conducted on myeloma cell line of mice found H-DNA structures in Cγ2a and Cγ2b, which participate in sister chromatid exchange.
The role of NE in schizophrenia has not been fully understood, but has stimulated research into this topic. The only relationship that has been understood between researchers is that there is a positive correlation between increased NE levels in the brain and spinal fluid (CSF) and activity of schizophrenia. In one study, clonidine, a drug used to treat medical conditions such as ADHD and high blood pressure, was shown to produce a significant decrease in plasma level MHPG (3-methoxy-4-hydroxyphenylglycol), a metabolite of NE, in the normal control group, but not in the group of schizophrenic patients. This suggests that in schizophrenia, the alpha-2 adrenergic receptor, a presynaptic inhibitory receptor, may be less sensitive compared to normally functioning alpha-2 receptors and thus relate to elevated NE levels in the disorder. In addition to increased NE levels in the brain and CSF, increased levels of MHPG has also been associated with a diagnosis of schizophrenia. Impaired NE regulation in schizophrenia has been an area of interest for researchers and research on this topic is still ongoing.
Sources: en.wikipedia.org
The pancreas is a major organ functioning as an accessory digestive gland in the digestive system. It is both an endocrine gland and an exocrine gland. The endocrine part secretes insulin when the blood sugar becomes high; insulin moves glucose from the blood into the muscles and other tissues for use as energy. The endocrine part releases glucagon when the blood sugar is low; glucagon allows stored sugar to be broken down into glucose by the liver in order to re-balance the sugar levels. The pancreas produces and releases important digestive enzymes in the pancreatic juice that it delivers to the duodenum. The pancreas lies below and at the back of the stomach. It connects to the duodenum via the pancreatic duct which it joins near to the bile duct's connection where both the bile and pancreatic juice can act on the chyme that is released from the stomach into the duodenum. Aqueous pancreatic secretions from pancreatic duct cells contain bicarbonate ions which are alkaline and help with the bile to neutralise the acidic chyme that is churned out by the stomach. The pancreas is also the main source of enzymes for the digestion of fats and proteins. Some of these are released in response to the production of cholecystokinin in the duodenum. (The enzymes that digest polysaccharides, by contrast, are primarily produced by the walls of the intestines.) The cells are filled with secretory granules containing the precursor digestive enzymes. The major proteases, the pancreatic enzymes which work on proteins, are trypsinogen and chymotrypsinogen. Elastase is also produced.
The submarines were under orders to report sightings before attempting to attack, so Flying Fish waited until nightfall, then surfaced to radio in its report. Fifth Fleet commander Spruance was convinced that a major battle was at hand. After consulting with Nimitz at Pacific Fleet Headquarters in Hawaii, he ordered Rear Admiral Marc Mitscher, commander of the Fast Carrier Task Force (Task Force 58), who had sent two carrier task groups north to intercept aircraft reinforcements from Japan, to reform and move west of Saipan into the Philippine Sea. TF 52's battleships, cruisers and escort carrier groups were ordered to remain near Saipan to protect the invasion fleet and provide air support for the landings. Shortly before midnight on 18 June Nimitz radioed Spruance that a Japanese vessel had broken radio silence. The message intercepted was an apparent dispatch from Ozawa to his land-based air forces on Guam. Radio direction-finding placed the sender approximately 355 miles (571 km) west-southwest of TF 58. Mitscher considered whether the radio messages were a Japanese deception, as the Japanese were known to send a single vessel off to break radio silence, to mislead their adversaries about the actual location of the main force. Mitscher realized that there was a chance of a night surface encounter with Ozawa's forces. Arleigh Burke, Mitscher's chief of staff (a former destroyer squadron commander who had won several night battles in the Solomons), assumed that battle line commander Willis Lee would welcome the opportunity. But Lee strongly opposed such an encounter.
Halliwell B, Watt F, Minqin R. (2023) Iron and atherosclerosis: Lessons learned from rabbits relevant to human disease. Free Radic. Biol. Med. 209, 165–170. Yau YF, Cheah IK, Mahendran R, Tang RMY, Chua RY, Goh RES, Feng L, Li J, Kua EH, Chen C, Halliwell B. (2024) Investigating the efficacy of ergothioneine to delay cognitive decline in mild cognitively impaired subjects: A pilot study. J. Alzheimer's Disease 102, 841–854.
Glutamic proteases are a group of proteolytic enzymes containing a glutamic acid residue within the active site. This type of protease was first described in 2004 and became the sixth catalytic type of protease. Members of this group of protease had been previously assumed to be an aspartate protease, but structural determination showed it to belong to a novel protease family. The first structure of this group of protease was scytalidoglutamic peptidase, the active site of which contains a catalytic dyad, glutamic acid (E) and glutamine (Q), which give rise to the name eqolisin. This group of proteases are found primarily in pathogenic fungi affecting plant and human.
Sources: en.wikipedia.org
However, the subsequent era under Leonid Brezhnev, sometimes referred to as the Era of Stagnation, was marked by economic decline, political corruption, and a rigid gerontocracy. Despite efforts to maintain the Soviet Union's superpower status, the economy struggled due to its centralized nature, technological backwardness, and inefficiencies. The vast military expenditures, and the Eastern Bloc halting embezzlement of its resources; further strained the Soviet economy. In the 1980s, Mikhail Gorbachev's policies of glasnost (openness) and perestroika (restructuring) aimed to revitalize the Soviet system but instead accelerated its unraveling. Nationalist movements gained momentum across the Soviet republics and the control of the Communist Party weakened. The failed coup attempt in August 1991 against Gorbachev by hardline communists hastened the end of the Soviet Union, which formally dissolved on 26 December 1991, ending nearly seven decades of Soviet rule.
A health facility is, in general, any location where healthcare is provided. Health facilities range from small clinics and doctor's offices to urgent care centers and large hospitals with elaborate emergency rooms and trauma centers. The number and quality of health facilities in a country or region is one common measure of that area's prosperity and quality of life. In many countries, health facilities are regulated to some extent by law; licensing by a regulatory agency is often required before a facility may open for business. Health facilities may be owned and operated by for-profit businesses, non-profit organizations, governments, and, in some cases, individuals, with proportions varying by country. See also the recent review paper,
Structural biology is concerned with the structural analysis of biological material at every level of organization. During the 19th and early 20th centuries, structural studies were largely limited to structures visible to the naked eye or through magnifying glasses and light microscopes. In the 20th century, a variety of experimental techniques were developed to examine the 3D structures of biological molecules. The most prominent techniques are X-ray crystallography, nuclear magnetic resonance, and electron microscopy. The discovery of X-rays and their application to protein crystals transformed structural biology by allowing researchers to determine the three-dimensional structures of biological molecules in atomic detail. Likewise, NMR spectroscopy allowed information about protein structure and dynamics to be obtained. Finally, in the 21st century, electron microscopy also saw a drastic revolution with the development of more coherent electron sources, aberration correction for electron microscopes, and reconstruction software that enabled the successful implementation of high resolution cryo-electron microscopy, thereby permitting the study of individual proteins and molecular complexes in three-dimensions at angstrom resolution.
Sources: en.wikipedia.org
System suitability is a set of checks performed before and during a run to confirm that the instrument, column, and method work as expected. Common checks include resolution, tailing factor, theoretical plates, and relative standard deviation of replicate injections. Failure triggers troubleshooting or method adjustment.
Validation demonstrates that a method produces reliable results for a defined purpose. It documents performance limits and acceptance criteria. Regulated industries require validation before routine testing of products or samples.
Retention time shifts can arise from changes in mobile phase composition, pH, temperature, column age, or flow rate. Contamination or worn seals may also alter pressure and delivery. Systematic checks of these factors help identify the cause.
System suitability is typically performed before each batch or according to the validated method and laboratory procedure. Some long runs include periodic checks during analysis. The required frequency depends on regulatory expectations and method performance.