If you have been reading about Calibration curve and want a single page that covers the useful parts, this is it: definitions, context, how it is studied, and the questions that come up repeatedly.
Last reviewed on 2026-06-29. Where a claim depends on a specific study, the study is described rather than over-claimed.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
Validation demonstrates that a method is suitable for its intended use. Typical performance characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulators and standards organizations provide frameworks, but specific requirements depend on the application and jurisdiction. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, retention time repeatability, and sensitivity. A validated method is not permanently fixed; changes may require partial or full revalidation.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
| Property | Value | Notes |
|---|---|---|
| Validation parameter | Accuracy | Closeness of measured value to accepted reference value |
| Validation parameter | Precision | Agreement among repeated measurements under specified conditions |
| System suitability check | Resolution ≥ 1.5 | Baseline separation between critical peak pair |
| System suitability check | Tailing factor ≤ 2.0 | Common target for peak symmetry |
| Documentation | Validation report | Summarizes experiments, acceptance criteria, and conclusions |
Method validation establishes that an HPLC procedure is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, robustness, and solution stability. Accuracy reflects closeness to a reference value, while precision reflects agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from matrix components. Validation is documented through protocols and reports, and the required extent depends on the method's use and regulatory context.
Routine quality control uses system suitability, blank injections, check standards, and control samples to detect drift or contamination. System suitability criteria may specify minimum resolution, maximum tailing factor, and a permitted range for repeated injections. Blank injections reveal carryover or solvent contamination, while check standards confirm calibration accuracy over a batch. Control samples with known analyte levels can show whether results remain within statistical limits. When a control result falls outside limits, the analyst investigates the cause and may invalidate affected results before repeating the batch.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
Laboratories apply HPLC testing across pharmaceutical, food, environmental, and industrial chemistry. The method can measure active ingredients, impurities, additives, preservatives, and degradation products. Sample preparation often includes dilution, filtration, and sometimes extraction or derivatization. The choice of column, mobile phase, pH, temperature, and detector depends on the analytes and matrix. Results are compared with reference standards to assign identity and concentration. Method suitability is judged by resolution, precision, and accuracy.
HPLC testing is not a single fixed procedure; it is a family of separation modes. Reversed-phase, normal-phase, ion-exchange, size-exclusion, and affinity chromatography each suit different analyte properties. Reversed-phase methods dominate because they handle many neutral and moderately polar compounds. Detection can be optical, electrochemical, or mass spectrometric, and the detector dictates what information is available. Coupling with mass spectrometry increases selectivity and enables identification when standards are unavailable. The technique cannot separate every mixture without adjustment.
Detection commonly uses ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. Ultraviolet detection depends on molecular chromophores that absorb light at specific wavelengths. Mass spectrometry provides mass information and sensitive quantification, often after electrospray ionization. Before sample batches, performance checks examine resolution, elution time repeatability, peak symmetry, and plate count. Matrix effects and co-elution remain recognized uncertainties; formal validation studies and orthogonal detection help address them. Detector choice depends on analyte properties and required sensitivity.
High-performance liquid chromatography, or HPLC, separates dissolved compounds by passing a liquid mobile phase through a packed column. Components distribute differently between the stationary phase and the moving liquid, so they travel at different speeds and exit at different times. A detector records these eluting bands as peaks, and peak area or height relates to amount. The technique supports testing in pharmaceuticals, foods, environmental samples, and industrial chemicals. Quantification usually depends on calibration with known standards.
Several separation modes exist, including reversed-phase, normal-phase, ion-exchange, size-exclusion, and hydrophilic interaction liquid chromatography. Reversed-phase uses a nonpolar stationary phase with a polar mobile phase and is widely applied to small organic molecules. Gradient elution changes mobile phase composition during the run, while isocratic elution keeps it constant. Column chemistry, particle size, temperature, flow rate, and mobile phase pH all influence retention and resolution. Method development selects conditions that separate analytes from matrix components and from each other.
In February 2026, the PRAC recommended that medicines containing levamisole be withdrawn from the EU market. This follows an EU-wide review which concluded that the benefits of these medicines no longer outweigh their risks for the treatment of parasitic worm infections in adults and children.
When a carbohydrate-rich food has been eaten before AMP has been eliminated from muscle cells, when bulk absorption starts, plenty of glucose becomes available in the blood, is taken up by muscle cells, is added to the glycogen store, but then immediately becomes liberated by the still up-regulated myophosphorylase. The resulting excess of glucose is metabolized down to lactic acid (the body cannot increase aerobic metabolism in an instant), recharging all AMP to ATP. The lactate is dumped back into blood and urine. The higher the glycemic index of the food is, the greater proportion of carbohydrates (and calories) is wasted into urine. If the person is at rest at this moment, and pays attention, a sudden increase in the breathing frequency due to lactate dumping is readily observable. If the rise in the blood lactate is particularly sharp, and the person happened to be breathing slowly, a heart palpitation may sometimes be observable. The lactic acidosis with palpitation may also occur during sleep, if stomach emptying has been delayed e.g. due to digestion requirements of the food or its high volume, and the person went to sleep before absorption has started. In this case the person will be awaken in a state of distress, with rapid breathing. The person may recall seeing a nightmare.
Boletus edulis is well suited to drying—its flavour intensifies, it is easily reconstituted, and its resulting texture is pleasant. Reconstitution is done by soaking in hot, but not boiling, water for about twenty minutes; the water used is infused with the mushroom aroma and it too can be used in subsequent cooking, after filtering out particulate matter such as fine grit. Dried porcini have more protein than most other commonly consumed vegetables, apart from soybeans. Some of their protein is indigestible, though digestibility is improved with cooking. Like other boletes, porcini can be dried by being strung separately on twine and hung close to the ceiling of a kitchen. Alternatively, the mushrooms can be dried by cleaning with a brush (washing is not recommended), and then placing them in a wicker basket or bamboo steamer on top of a boiler or hot water tank. Another method is drying in an oven at 25 to 30 °C (77 to 86 °F) for two to three hours, then increasing the temperature to 50 °C (122 °F) until crisp or brittle. Once dry, they must be kept in an airtight container. Importantly for commercial production, porcini retain their flavour after industrial preparation in a pressure cooker or after canning or bottling, and are thus useful for manufacturers of soups or stews. The addition of a few pieces of dried porcino can significantly add to flavour, and they are a major ingredient of the pasta sauce known as carrettiera (carter's sauce). The drying process is known to induce the formation of various volatile substances that contribute to the mushroom's aroma.
=== Applications of mechanical bonding in controlling chemical reactivity === The ability for a mechanical bond to reduce reactivity and hence prevent unwanted reactions has been exploited in a number of areas. One of the earliest applications was in the protection of organic dyes from environmental degradation.
Sources: en.wikipedia.org
==== MeSH D12.776.964.950.800 – trans-activators ==== MeSH D12.776.964.950.800.385 – gene products, rev (HIV) MeSH D12.776.964.950.800.400 – gene products, tat MeSH D12.776.964.950.800.410 – gene products, tax MeSH D12.776.964.950.800.430 – gene products, vpr MeSH D12.776.964.950.800.445 – herpes simplex virus protein vmw65
=== Brand names === Brand names of flutamide include or have included Cebatrol, Cytomid, Drogenil, Etaconil, Eulexin, Flucinom, Flumid, Flutacan, Flutamid, Flutamida, Flutamin, Flutan, Flutaplex, Flutasin, Fugerel, Profamid, and Sebatrol, among others.
The three substrates of this enzyme are (2S,4S)-4-hydroxy-2,3,4,5-tetrahydrodipicolinic acid, reduced nicotinamide adenine dinucleotide (NADH), and a proton. Its products are (S)-2,3,4,5-tetrahydrodipicolinic acid], oxidised NAD+ and water. Nicotinamide adenine dinucleotide phosphate can be used as an alternative cofactor. This enzyme is part of the biosynthesis pathway to lysine.
Sources: en.wikipedia.org
BDPC (systematic name 4-(4-bromophenyl)-4-(dimethylamino)-1-(2-phenylethyl)cyclohexanol; also known as bromadol) is a potent fully synthetic opioid with a distinctive arylcyclohexylamine chemical structure. It was developed by Daniel Lednicer at Upjohn in the 1970s. Initial studies estimated that it was around 10,000 times the potency of morphine in animal models. However, later studies using more modern techniques assigned a value of 504 times the potency of morphine for the more active trans-isomer. This drug was first seized along with three kilograms of acetylfentanyl in an April 25, 2013 police action in Montreal, Canada, and has reportedly continued to be available on the designer drug market internationally. Analogues where the para-bromine is replaced by chlorine or a methyl group retain similar activity, while the meta-hydroxyl derivative demonstrated robust antagonist activity.
transition, which has been considered for the creation of a transportable optical clock as all transitions necessary for clock operation can be addressed with direct diode lasers at common wavelengths. Some of the few practical uses of radium are derived from its radioactive properties. More recently discovered radioisotopes, such as cobalt-60 and caesium-137, are replacing radium in even these limited uses because several of these isotopes are more powerful emitters, safer to handle, and available in more concentrated form. The isotope 223Ra was approved by the United States Food and Drug Administration in 2013 for use in medicine as a cancer treatment of bone metastasis in the form of a solution including radium-223 chloride. The main indication of treatment is the therapy of bony metastases from castration-resistant prostate cancer. 225Ra has also been used in experiments concerning therapeutic irradiation, as it is the only reasonably long-lived radium isotope which does not have radon as one of its daughters. Radium was still used in 2007 as a radiation source in some industrial radiography devices to check for flawed metallic parts, similarly to X-ray imaging. When mixed with beryllium, radium acts as a neutron source. Up until at least 2004, radium-beryllium neutron sources were still sometimes used, but other materials such as polonium and americium have become more common for use in neutron sources. RaBeF4-based (α, n) neutron sources have been deprecated despite the high number of neutrons they emit (1.84×106 neutrons per second) in favour of 241Am–Be sources.
==== Role in myocardial growth and adaptation ==== Intracrine PTHrP has been implicated in myocardial development and adaptation to stress. It is particularly active during embryonic heart development, where it influences cardiomyocyte differentiation and growth. Additionally, under conditions of cardiac stress, such as ischemia or hypertrophy, PTHrP expression is upregulated, suggesting a protective role in maintaining myocardial function. Moreover, in vascular smooth muscle cells, intracrine PTHrP plays a dual role. While secreted PTHrP can inhibit cell proliferation via receptor-mediated pathways, intracellular PTHrP exerts a mitogenic effect, promoting vascular remodeling and adaptation in response to hemodynamic changes.
Sources: en.wikipedia.org
It is a set of checks performed before or during an HPLC run to confirm the system works as expected. Parameters may include resolution, tailing factor, theoretical plates, and retention time precision. Failure can trigger maintenance, method adjustment, or repeat analysis.
Validation follows a planned protocol that tests accuracy, precision, specificity, linearity, range, detection limits, quantitation limits, and robustness. Results are compared against predefined acceptance criteria. The validation report supports regulatory filing or routine use.
Revalidation may be needed after changes to column chemistry, mobile phase, detection, sample preparation, or instrument type. It can also follow a pattern of out-of-specification results. The scope depends on whether the change affects method performance.
Method validation is the documented process of showing that an HPLC procedure produces reliable results for a defined purpose. It examines parameters such as accuracy, precision, specificity, linearity, and robustness. Regulators and quality systems often require validation before routine use.