This is a working overview of HPLC, written for readers who want more than a one-paragraph summary but less than a textbook.
Reviewed 2026-05-12. Anything still debated is marked as such rather than presented as settled.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Common checks include retention time, peak area, resolution between critical pairs, tailing factor, and theoretical plate count. Results are compared with predefined limits, and a failed check requires investigation before sample results are reported. Quality control samples at low, middle, and high concentrations are injected at intervals to monitor accuracy and precision. Blank injections detect carryover and contamination, while control charts track performance over time.
Data handling and documentation are central to HPLC quality control. Electronic systems should have audit trails that record changes to methods, sequences, and results. Integration parameters, such as peak baseline and threshold, can affect reported areas and must be defined in advance. Out-of-specification results trigger a structured investigation that may include reanalysis, instrument checks, and review of sample preparation. Regulatory inspections often examine raw data, audit trails, and training records to verify that reported results are traceable and reliable.
HPLC testing separates dissolved compounds by passing a liquid sample through a column packed with stationary phase. A pump delivers mobile phase at controlled flow, and the sample components interact differently with stationary and mobile phases. Compounds that spend more time in mobile phase elute earlier; those retained by stationary phase elute later. Detectors record elution as peaks, and peak area or height relates to amount. This mechanism underpins quantitative analysis of mixtures.
Most routine HPLC testing uses reversed-phase columns, where the stationary phase is nonpolar and the mobile phase is a polar mixture such as water with an organic solvent. Analytes partition between the two phases according to polarity, size, and charge. Gradients that change solvent composition over time can separate compounds with broad retention ranges. Isocratic conditions keep solvent composition constant and suit simpler mixtures. The choice of column chemistry, pH, and temperature affects selectivity and peak shape.
| Property | Value | Notes |
|---|---|---|
| Validation parameter | Accuracy | Measured value compared with true or accepted value |
| Precision type | Repeatability | Same analyst, instrument, and short time interval |
| Linearity range | 50–150% of target concentration | Common for assay methods; method-dependent |
| Limit of quantitation | Signal-to-noise ratio of 10:1 | Lowest concentration with acceptable precision |
| Common synonyms | Method validation, analytical validation | Documented confirmation that a method is suitable |
Developing an HPLC test begins with defining the analytes, matrix, and required reporting limits. Chemists select a separation mode, column chemistry, mobile phase composition, flow rate, and detection wavelength or mass transition. Experiments then adjust these variables to achieve adequate retention, resolution, and peak shape. System suitability tests confirm that the instrument and method perform consistently before sample analysis. Without suitable resolution, quantitative results may be unreliable. Preliminary runs often use scouting gradients to locate retention windows.
Validation establishes that a method is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, robustness, and stability of standards and samples. Acceptance criteria are defined in advance, and results are documented in a validation report. Regulatory guidance for pharmaceuticals, foods, and environmental testing differs, so the applicable framework must be identified. Ongoing verification uses control samples and trend charts after validation. Method transfer to another laboratory may require partial revalidation.
Routine quality control includes blanks, duplicates, spiked samples, and certified reference materials. Calibration curves are prepared with standards at several concentrations, and the detector response is checked for linearity. Carryover, column aging, mobile phase evaporation, and temperature drift can shift retention times or peak areas. Maintenance such as replacing seals, filters, and columns helps prevent failures. Records of injections, integration, and deviations support traceability. Audits may request raw data and instrument logs for each batch.
High-performance liquid chromatography, or HPLC, separates dissolved compounds by passing a liquid mobile phase through a packed column. Components distribute differently between the stationary phase and the moving liquid, so they travel at different speeds and exit at different times. A detector records these eluting bands as peaks, and peak area or height relates to amount. The technique supports testing in pharmaceuticals, foods, environmental samples, and industrial chemicals. Quantification usually depends on calibration with known standards.
Several separation modes exist, including reversed-phase, normal-phase, ion-exchange, size-exclusion, and hydrophilic interaction liquid chromatography. Reversed-phase uses a nonpolar stationary phase with a polar mobile phase and is widely applied to small organic molecules. Gradient elution changes mobile phase composition during the run, while isocratic elution keeps it constant. Column chemistry, particle size, temperature, flow rate, and mobile phase pH all influence retention and resolution. Method development selects conditions that separate analytes from matrix components and from each other.
Method validation establishes that an HPLC procedure is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, robustness, and solution stability. Accuracy reflects closeness to a reference value, while precision reflects agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from matrix components. Validation is documented through protocols and reports, and the required extent depends on the method's use and regulatory context.
Routine quality control uses system suitability, blank injections, check standards, and control samples to detect drift or contamination. System suitability criteria may specify minimum resolution, maximum tailing factor, and a permitted range for repeated injections. Blank injections reveal carryover or solvent contamination, while check standards confirm calibration accuracy over a batch. Control samples with known analyte levels can show whether results remain within statistical limits. When a control result falls outside limits, the analyst investigates the cause and may invalidate affected results before repeating the batch.
=== Reversal potential === Even if both K+ and Na+ ions have the same charge, they can still have very different equilibrium potentials for both outside and/or inside concentrations. The sodium-potassium pump moves toward a nonequilibrium state with the relative concentrations of Na+ and K+ for both inside and outside of cell. For instance, the concentration of K+ in cytosol is 100-140 mM, whereas the concentration of Na+ is 5-15 mM. On the other hand, in extracellular space, the usual concentration range of K+ is about 3.5-5 mM, whereas the concentration of Na+ is about 135-145 mM.
=== 1989 local government reforms === For many decades until the local government reforms of 1989, a borough with more than 20,000 people could be proclaimed a city. The boundaries of councils tended to follow the edge of the built-up area, so little distinction was made between the urban area and the local government area. New Zealand's local government structural arrangements were significantly reformed by the Local Government Commission in 1989 when approximately 700 councils and special purpose bodies were amalgamated to create 87 new local authorities. Regional councils were reduced in number from 20 to 13, territorial authorities (city/district councils) from 200 to 75, and special purpose bodies from over 400 to 7. The new district and city councils were generally much larger and most covered substantial areas of both urban and rural land. Many places that once had a city council were now being administered by a district council. As a result, the term "city" began to take on two meanings. City also came to be used in a less formal sense to describe major urban areas independent of local body boundaries. This informal usage is jealously guarded. Gisborne, for example, adamantly described itself as the first city in the world to see the new millennium. Gisborne is administered by a district council, but its status as a city is not generally disputed. Under current law, an urban area has to be at least 50,000 residents before it can be officially proclaimed as a city.
=== Leukocyte adhesion deficiency and the "multistep paradigm" === Working with physicians seeing patients with recurring, life-threatening bacterial infections, Springer found their leukocytes lacked LFA-1 (αLβ2), Mac-1 (αMβ2), and αXβ2. Anderson and Springer named the disease leukocyte adhesion deficiency (LAD) in a review article, and it was shown to be caused by mutations in the β2 subunit common to the leukocyte integrins. Patients have abnormally high levels of neutrophils in their circulation, which cannot emigrate out of the bloodstream to fight infection. This demonstrated that β2 integrins were important in leukocyte interactions with vascular endothelial cells and stimulated Springer to set up work in the lab on endothelial cells and flow chambers. In related work on LFA-1 ligands, ICAM-1 and ICAM-2 were shown to be inducible and constitutively expressed, respectively, on endothelium. It had long been known from intravital microscopy that leukocyte emigration involved leukocyte rolling on endothelium followed by firm adhesion and subsequent transendothelial migration. Using white blood cells infused in flow chambers and purified adhesion molecules on the chamber walls under physiological shear rates found in vivo, Springer and postdoctoral fellow Mike Lawrence reconstituted three sequential interactions required for leukocyte emigration. Flow chamber walls were coated with P-selectin, ICAM-1, or both. Infused neutrophils were found to readily attach and then roll on P-selectin, but could not attach to ICAM-1 in flow.
Sources: en.wikipedia.org
=== VfB Leipzig (1893–1946) === The club was formed as VfB Leipzig on 13 May 1896, out of the football department of the gymnastics club Allgemeine Turnverein 1845 Leipzig. However, the club laid claim to an earlier date of origin by referring back to a club that was merged with VfB Leipzig in 1898, the SC Sportbrüder Leipzig, which was one of four football clubs formed in Leipzig in 1893. Following the merger with SC Sportbrüder Leipzig, the club competed under the name VfB Sportbrüder 1893 Leipzig. VfB Sportbrüder 1893 Leipzig was one of the original 86 teams that came together in the city on 28 January 1900 to form the German Football Association (DFB). On 2 May 1900, the Sportbrüder 1893 part of the name was dropped, and the team became again known as VfB Leipzig.
== Production == Approximately 1.5 million tons were produced in 1985, typically by the reaction of potassium chloride with sulfuric acid, analogous to the Mannheim process for producing sodium sulfate. The process involves intermediate formation of potassium bisulfate, an exothermic reaction that occurs at room temperature:
=== Atmosphere of Mars === In 2013, OH near-infrared spectra were observed in the night glow in the polar winter atmosphere of Mars by use of the Compact Reconnaissance Imaging Spectrometer for Mars (CRISM).
Sources: en.wikipedia.org
System suitability is a set of checks that confirm the instrument and method perform within limits before sample analysis. It typically includes resolution, tailing factor, retention time, and peak area reproducibility. If a check fails, the run is invalidated until the cause is resolved.
QC samples are usually injected at the beginning, at intervals during the run, and at the end. The exact frequency depends on the method, sample count, and regulatory requirements. Results outside acceptance limits can require rejection of the affected samples and investigation.
Method validation demonstrates that an HPLC procedure produces reliable results for its intended purpose. It provides documented evidence for accuracy, precision, specificity, and other performance characteristics. Regulators and quality systems require validation before a method is used for release or stability testing.
It separates components in a liquid sample and measures their amounts using a detector. Results can indicate concentration, purity, or identity based on retention time and detector response. The technique works for mixtures that can be dissolved and filtered.