A practical reference on quality control: what it is, how it behaves, what the literature reports, and where the honest uncertainties sit.
This page was last updated on 2026-08-01 and is reviewed periodically as new material appears.
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
Routine quality control monitors retention time shifts, baseline noise, system pressure, and peak shape. Trends can reveal column aging, mobile phase preparation errors, detector drift, or sample degradation. Corrective actions may include replacing the column, preparing fresh mobile phase, or recalibrating the detector. Stability testing often uses HPLC to measure parent compound loss and degradation product formation. Open questions remain about how accelerated stability results extrapolate to long-term storage under varied conditions.
Quality control for HPLC testing combines scheduled checks, documented procedures, and review of results. Before sample analysis, system suitability testing confirms that the instrument, column, and method meet predefined criteria. Common criteria include resolution between critical peaks, retention time precision, peak tailing, and theoretical plate count. Failure triggers investigation before results are reported. Records link raw data, calculations, instrument logs, and analyst identity to each batch, supporting audits and repeat analysis.
| Property | Value | Notes |
|---|---|---|
| Validation parameter | Accuracy | Closeness to a reference value. |
| Validation parameter | Precision | Repeatability or intermediate precision. |
| Validation parameter | Linearity | Proportional response across a range. |
| System suitability check | Resolution | Separation between adjacent peaks. |
| Quality control tool | Control chart | Tracks results over time for trends. |
Routine quality control uses system suitability, blank injections, check standards, and control samples to detect drift or contamination. System suitability criteria may specify minimum resolution, maximum tailing factor, and a permitted range for repeated injections. Blank injections reveal carryover or solvent contamination, while check standards confirm calibration accuracy over a batch. Control samples with known analyte levels can show whether results remain within statistical limits. When a control result falls outside limits, the analyst investigates the cause and may invalidate affected results before repeating the batch.
Documentation and traceability are central to regulated HPLC testing. Records typically include instrument logs, column history, mobile-phase preparation, sample preparation, injection sequences, raw chromatograms, and audit trails. Electronic systems may require user access controls, time-stamped changes, and backup procedures. Training records show that analysts are qualified for assigned methods. Audits and inspections check whether written procedures match actual practice and whether deviations are documented. These controls support reproducibility and allow results to be reconstructed if questions arise later.
Method validation establishes that an HPLC procedure is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, robustness, and solution stability. Accuracy reflects closeness to a reference value, while precision reflects agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from matrix components. Validation is documented through protocols and reports, and the required extent depends on the method's use and regulatory context.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. A diode array detector records full spectra across a wavelength range, which helps identify co-eluting peaks. Mass spectrometry provides mass-to-charge ratios and can confirm molecular identity at low concentrations. The choice of detector depends on analyte structure, required sensitivity, and whether quantitation or identification is the goal. No single detector works for every compound, and method development often compares responses before selecting one.
High-performance liquid chromatography is an analytical technique that separates components of a liquid sample by passing it through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in interaction with the stationary phase cause analytes to migrate at different rates. Detectors record elution as peaks, and a data system converts signals into a chromatogram. The method is suited to compounds that dissolve in a liquid and are not volatile enough for gas chromatography.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
HPLC testing separates dissolved compounds by passing a liquid sample through a column packed with stationary phase. A pump delivers mobile phase at controlled flow, and the sample components interact differently with stationary and mobile phases. Compounds that spend more time in mobile phase elute earlier; those retained by stationary phase elute later. Detectors record elution as peaks, and peak area or height relates to amount. This mechanism underpins quantitative analysis of mixtures.
Most routine HPLC testing uses reversed-phase columns, where the stationary phase is nonpolar and the mobile phase is a polar mixture such as water with an organic solvent. Analytes partition between the two phases according to polarity, size, and charge. Gradients that change solvent composition over time can separate compounds with broad retention ranges. Isocratic conditions keep solvent composition constant and suit simpler mixtures. The choice of column chemistry, pH, and temperature affects selectivity and peak shape.
== Incidence == Insulinomas are rare neuroendocrine tumours with an incidence estimated at one to four new cases per million persons per year. Insulinoma is one of the most common types of tumours arising from the islets of Langerhans cells (pancreatic endocrine tumours). Estimates of malignancy (metastases) range from 5 to 30%. Over 99% of insulinomas originate in the pancreas, with rare cases from ectopic pancreatic tissue. About 5% of cases are associated with tumours of the parathyroid glands and the pituitary (multiple endocrine neoplasia type 1) and are more likely to be multiple and malignant. Most insulinomas are small, less than 2 cm.
== Diagnostic use == Prolactin levels may be checked as part of a sex hormone workup, as elevated prolactin secretion can suppress the secretion of follicle stimulating hormone and gonadotropin-releasing hormone, leading to hypogonadism and sometimes causing erectile dysfunction. Prolactin levels may be of some use in distinguishing epileptic seizures from psychogenic non-epileptic seizures. The serum prolactin level usually rises following an epileptic seizure.
=== Raynaud's phenomenon === Sildenafil and other PDE5 inhibitors are used off-label to alleviate vasospasm and treat severe ischemia and ulcers in fingers and toes for people with secondary Raynaud's phenomenon; these drugs have moderate efficacy for reducing the frequency and duration of vasospastic episodes. As of 2016, their role more generally in Raynaud's was not clear.
The two substrates of this enzyme are D-glucose and oxidised nicotinamide adenine dinucleotide phosphate (NADP+). Its products are glucono-δ-lactone, reduced NADPH, and a proton. This enzyme belongs to the family of oxidoreductases, specifically those acting on the CH-OH group of donor with NAD+ or NADP+ as acceptor. The systematic name of this enzyme class is D-glucose:NADP+ 1-oxidoreductase. Other names in common use include nicotinamide adenine dinucleotide phosphate-linked aldohexose, dehydrogenase, NADP+-linked aldohexose dehydrogenase, NADP+-dependent glucose dehydrogenase, and glucose 1-dehydrogenase (NADP+).
In the following days, moral support was followed by material support. Large quantities of food, medicine, clothing, medical equipment, and other humanitarian aid were sent to Romania. Around the world, the press dedicated entire pages and sometimes even complete issues to the Romanian revolution and its leaders. On 24 December, Bucharest was still a city at war. Tanks, APCs and trucks continued to patrol the city and surround trouble spots in order to protect them. At intersections near strategic objectives, roadblocks were built; automatic gunfire continued in and around University Square, the Gara de Nord (the city's main railroad station) and Palace Square. Yet amid the chaos, some people were seen clutching makeshift Christmas trees. Doctors at one Bucharest hospital reported not sleeping for days and treating as many as 3,000 civilians due to the fighting. "Terrorist activities" continued until 27 December, when they abruptly stopped. Nobody ever found out who conducted them, or who ordered them stopped. The Central University Library was burned down in uncertain circumstances and over 500,000 books, along with about 3,700 manuscripts, were destroyed.
Sources: en.wikipedia.org
== History == Glucose was first isolated from raisins in 1747 by the German chemist Andreas Marggraf. Glucose was discovered in grapes by another German chemist, Johann Tobias Lowitz, in 1792, and distinguished as being different from cane sugar (sucrose). Glucose is the term coined by Jean-Baptiste Dumas in 1838, which has prevailed in the chemical literature. Friedrich August Kekulé proposed the term dextrose (from the Latin dexter, meaning "right"), because in aqueous solutions of glucose, the plane of linearly polarized light is turned to the right. In contrast, l-fructose (usually referred to as l-fructose) (a ketohexose) and l-glucose (l-glucose) turn linearly polarized light to the left. The earlier notation according to the rotation of the plane of linearly polarized light (d and l-nomenclature) was later abandoned in favor of the d- and l-notation, which refers to the absolute configuration of the asymmetric center furthest from the carbonyl group, and in concordance with the configuration of d- or l-glyceraldehyde. Since glucose is a basic necessity of many organisms, a correct understanding of its chemical makeup and structure contributed greatly to a general advancement in organic chemistry. This understanding occurred largely as a result of the investigations of Hermann Emil Fischer, a German chemist who received the 1902 Nobel Prize in Chemistry for his findings.
=== Religious organizations === Celtic Reconstructionism, a form of Polytheism Congregation of Clerics Regular of the Divine Providence (Theatines), a Roman Catholic religious order Community of the Resurrection, an Anglican religious order Congregation of the Resurrection, a Catholic religious order
=== BASF refounded (1952) === On 28 July 1948, an explosion occurred at a BASF site in Ludwigshafen, killing 207 people and injuring 3818. In 1952, BASF was refounded under its name following the efforts of former Nazi Party member Carl Wurster, who served in Nazi Germany as Wehrwirtschaftsführer (war economy leader). With the German economic miracle in the 1950s, BASF added synthetics such as nylon to its product range. BASF developed Polystyrene in the 1930s and invented Styropor in 1951.
== Examples == Examples of dough conditioners include ascorbic acid, distilled monoglycerides, citrate ester of monoglycerides, diglycerides, ammonium chloride, enzymes, diacetyl tartaric acid ester of monoglycerides or DATEM, potassium bromate, potassium iodate, calcium salts such as calcium iodate, L-cystine, L-cysteine HCl, glycerol monostearate, azodicarbonamide, sodium stearoyl lactylate, sucrose palmitate or other sucrose esters, polyoxyethylene sorbitan monostearate or polysorbate, soybean lecithin, and soybean lecithin enriched with lysophospholipids. Less processed dough conditioners include sprouted- or malted-grain flours, soy, milk, wheat germ, eggs, potatoes, gluten, yeast, and extra kneading. Malted, diastatic flours are not typically added by manufacturers to whole-wheat flours.
Sources: en.wikipedia.org
Method validation is the documented process of showing that an HPLC procedure produces reliable results for a defined purpose. It examines parameters such as accuracy, precision, specificity, linearity, and robustness. Regulators and quality systems often require validation before routine use.
System suitability is a set of checks run on the chromatographic system before sample analysis. It confirms that resolution, peak shape, retention time, and response meet predefined limits. Failure can invalidate the run and trigger corrective action.
Blank injections reveal peaks or baseline disturbances that come from solvents, reagents, or the instrument rather than the sample. They help distinguish contamination from actual analyte signals. Comparing blanks with sample runs supports accurate interpretation.
System suitability is typically performed before each batch or according to the validated method and laboratory procedure. Some long runs include periodic checks during analysis. The required frequency depends on regulatory expectations and method performance.