quality control comes up often in conversation and rarely with the context attached. Here we lay out the basics in order, then work through the practical considerations.
Last reviewed on 2025-09-11. Where a claim depends on a specific study, the study is described rather than over-claimed.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. A diode array detector records full spectra across a wavelength range, which helps identify co-eluting peaks. Mass spectrometry provides mass-to-charge ratios and can confirm molecular identity at low concentrations. The choice of detector depends on analyte structure, required sensitivity, and whether quantitation or identification is the goal. No single detector works for every compound, and method development often compares responses before selecting one.
High-performance liquid chromatography is an analytical technique that separates components of a liquid sample by passing it through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in interaction with the stationary phase cause analytes to migrate at different rates. Detectors record elution as peaks, and a data system converts signals into a chromatogram. The method is suited to compounds that dissolve in a liquid and are not volatile enough for gas chromatography.
Reversed-phase chromatography dominates modern HPLC testing, using a nonpolar stationary phase such as chemically bonded octadecyl groups and a polar mobile phase of water mixed with organic solvent. Analytes partition between the mobile and stationary phases according to hydrophobicity. Gradient elution changes the mobile phase composition over time to separate compounds with a wide range of retention. Isocratic elution keeps the composition constant and is simpler for routine assays. Column temperature, pH, and flow rate influence selectivity, peak shape, and retention time, so these parameters are controlled during a validated method.
Routine quality control includes blanks, duplicates, spiked samples, and certified reference materials. Calibration curves are prepared with standards at several concentrations, and the detector response is checked for linearity. Carryover, column aging, mobile phase evaporation, and temperature drift can shift retention times or peak areas. Maintenance such as replacing seals, filters, and columns helps prevent failures. Records of injections, integration, and deviations support traceability. Audits may request raw data and instrument logs for each batch.
Developing an HPLC test begins with defining the analytes, matrix, and required reporting limits. Chemists select a separation mode, column chemistry, mobile phase composition, flow rate, and detection wavelength or mass transition. Experiments then adjust these variables to achieve adequate retention, resolution, and peak shape. System suitability tests confirm that the instrument and method perform consistently before sample analysis. Without suitable resolution, quantitative results may be unreliable. Preliminary runs often use scouting gradients to locate retention windows.
Validation establishes that a method is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, robustness, and stability of standards and samples. Acceptance criteria are defined in advance, and results are documented in a validation report. Regulatory guidance for pharmaceuticals, foods, and environmental testing differs, so the applicable framework must be identified. Ongoing verification uses control samples and trend charts after validation. Method transfer to another laboratory may require partial revalidation.
| Property | Value | Notes |
|---|---|---|
| Separation mode | Reversed-phase | Most common for neutral and moderately polar analytes |
| Column particle size | 3–5 µm | Smaller particles improve resolution but raise backpressure |
| Mobile phase pH range | 2–8 | Silica-based columns may degrade outside this range |
| Typical flow rate | 1.0–2.0 mL/min | For analytical columns with 4.6 mm internal diameter |
| Common synonyms | HPLC, LC, high-pressure liquid chromatography | High-performance liquid chromatography is the standard expansion |
Practical HPLC testing depends on careful sample preparation and instrument maintenance. Samples may require filtration, dilution, pH adjustment, or extraction to avoid column damage and matrix interference. Mobile phases are degassed and filtered, and columns are equilibrated before injection. Common problems include peak tailing, baseline drift, ghost peaks, carryover, and co-elution of analytes. Documentation of instrument logs, calibration records, and electronic audit trails supports data integrity and traceability. Ongoing training and routine maintenance help reduce variability between analysts and laboratories.
Quality control laboratories use HPLC to check identity, purity, concentration, and stability of raw materials and finished products. A validated method specifies the column, mobile phase, flow rate, detection wavelength, injection volume, and run time. Samples are prepared and compared against reference standards of known concentration. The resulting chromatogram provides quantitative data, such as assay values and impurity levels. This approach is common in pharmaceutical, food, environmental, and industrial testing where consistent measurements are required.
Method validation demonstrates that an analytical procedure is suitable for its intended purpose. Typical validation characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulatory guidance from bodies such as the International Council for Harmonisation and the United States Pharmacopeia outlines expectations, though specific criteria depend on the product and method. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, column efficiency, and injection repeatability. Failure of these checks can invalidate a batch of measurements.
Laboratories apply HPLC testing across pharmaceutical, food, environmental, and industrial chemistry. The method can measure active ingredients, impurities, additives, preservatives, and degradation products. Sample preparation often includes dilution, filtration, and sometimes extraction or derivatization. The choice of column, mobile phase, pH, temperature, and detector depends on the analytes and matrix. Results are compared with reference standards to assign identity and concentration. Method suitability is judged by resolution, precision, and accuracy.
HPLC testing is not a single fixed procedure; it is a family of separation modes. Reversed-phase, normal-phase, ion-exchange, size-exclusion, and affinity chromatography each suit different analyte properties. Reversed-phase methods dominate because they handle many neutral and moderately polar compounds. Detection can be optical, electrochemical, or mass spectrometric, and the detector dictates what information is available. Coupling with mass spectrometry increases selectivity and enables identification when standards are unavailable. The technique cannot separate every mixture without adjustment.
HPLC testing is an analytical technique used to separate, identify, and quantify components in a liquid sample. It relies on a pressurized mobile phase that carries the sample through a column packed with stationary phase. Different compounds travel at different rates because of interactions with the stationary and mobile phases. The resulting signal versus time is a chromatogram. Peak position indicates identity under specified conditions, while peak area or height relates to amount.
Method validation establishes that an HPLC procedure is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, robustness, and solution stability. Accuracy reflects closeness to a reference value, while precision reflects agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from matrix components. Validation is documented through protocols and reports, and the required extent depends on the method's use and regulatory context.
Routine quality control uses system suitability, blank injections, check standards, and control samples to detect drift or contamination. System suitability criteria may specify minimum resolution, maximum tailing factor, and a permitted range for repeated injections. Blank injections reveal carryover or solvent contamination, while check standards confirm calibration accuracy over a batch. Control samples with known analyte levels can show whether results remain within statistical limits. When a control result falls outside limits, the analyst investigates the cause and may invalidate affected results before repeating the batch.
Validation demonstrates that a method is suitable for its intended use. Typical performance characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulators and standards organizations provide frameworks, but specific requirements depend on the application and jurisdiction. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, retention time repeatability, and sensitivity. A validated method is not permanently fixed; changes may require partial or full revalidation.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
== Road traffic death rate == The World Health Organization's (WHO) Global Status Report on Road Safety 2018 reported Thailand as having the world's sixth highest "estimated road traffic death rate per 100,000 population" (2016 figures). Four of the top death rates occur in African nations. They, and the Dominican Republic, are the only countries to exceed Thailand's death rate. Among ASEAN nations, Thailand was ranked one, with 32.7 deaths per 100,000 persons; Vietnam, 26.4; Malaysia, 23.6; Myanmar, 19.9; Cambodia, 17.8; Laos, 16.6; Philippines, 12.3; Indonesia, 12.2; Singapore, 2.8. Global Status Report on Road Safety 2015: Thailand has an "Estimated Road Traffic Death Rate" of 36.2 persons per 100,000 population, ranked 2 of 180 countries (1: worst, 180: best). Seventy-three percent of fatalities involved two- or three-wheeled motorized vehicles. In other ASEAN countries, corresponding death rates were: Vietnam, 24.5; Malaysia, 24; Myanmar, 20.3; Cambodia, 17.4; Indonesia, 15.3; Laos, 14.3; Philippines, 10.5; Singapore, 3.6.
== Further reading == Peter Harper; Lois Reynolds; Tilli Tansey, eds. (2010). Clinical Genetics in Britain: Origins and development. Wellcome Witnesses to Contemporary Medicine. History of Modern Biomedicine Research Group. ISBN 978-0-85484-127-1. Wikidata Q29581774.
=== Enzymatic method for RNA oligonucleotide synthesis === One approach under investigation for overcoming length limitations in oligonucleotide synthesis involves the use of engineered enzymes to construct RNA sequences, rather than relying solely on traditional chemical methods. A key enzyme studied in this context is CID1 poly(U) polymerase (PUP), which naturally catalyzes the addition of nucleotides to the 3′ end of an RNA strand. In its native form, PUP functions as a template-independent polymerase, typically adding repeated sequence nucleotide tails to RNA molecules. To enable controlled sequence synthesis, enzymatic RNA synthesis has been adapted into a cyclic two-step process consisting of nucleotide extension and deblocking. During the extension step, a single nucleotide is enzymatically added, while the deblocking step removes a protecting group to allow subsequent incorporation. One investigated method involves the use of nucleoside triphosphates modified with a 3′-O-allyl blocking group. These modified nucleotides are synthesized and purified using techniques such as ion-exchange chromatography and preparative high-performance liquid chromatography (HPLC). Upon incorporation by PUP, the 3′-O-allyl group prevents further extension, thereby enabling single-nucleotide addition per cycle. Chemical removal of the blocking group then permits the next round of extension. Studies have shown that wild-type PUP exhibits limited efficiency when incorporating modified nucleotides.
Prepared commercial blends may be sold as a powder or as a concentrated gelatinous block, divided into small squares. Either type is mixed with sufficient hot water to completely dissolve it, and then mixed with enough cold water to make the volume of liquid specified on the packet. The solubility of powdered gelatine can be enhanced by sprinkling it into the liquid several minutes before heating, "blooming" the individual granules. The fully dissolved mixture is then refrigerated, slowly forming a colloidal gel as it cools. Gelatine desserts may be enhanced in many ways, such as using decorative moulds, creating multicoloured layers by adding a new layer of slightly cooled liquid over the previously solidified one, or suspending non-soluble edible elements such as marshmallows or fruit. Some types of fresh fruit and their unprocessed juices are incompatible with gelatine desserts; see the Chemistry section below. When fully chilled, the most common ratios of gelatine to liquid (as instructed on commercial packaging) usually result in a custard-like texture which can retain detailed shapes when cold but melts back to a viscous liquid when warm. A recipe calling for the addition of additional gelatine to regular jelly gives a rubbery product that can be cut into shapes with cookie cutters and eaten with fingers (called "Knox Blox" by the Knox company, makers of unflavoured gelatine). Higher gelatine ratios can be used to increase the stability of the gel, culminating in gummy candies which remain rubbery solids at room temperature (see Bloom (test)).
=== Mechanism of action === While it is unclear how fluoxetine exerts its effect on mood, it has been suggested that fluoxetine elicits an antidepressant effect by inhibiting serotonin reuptake in the synapse by binding to the reuptake pump on the neuronal membrane to increase serotonin availability and enhance neurotransmission. Over time, this leads to a downregulation of pre-synaptic 5-HT1A receptors, which is associated with an improvement in passive stress tolerance, and delayed downstream increase in expression of brain-derived neurotrophic factor, which may contribute to a reduction in negative affective biases. Norfluoxetine and desmethylfluoxetine are metabolites of fluoxetine and also act as serotonin reuptake inhibitors, increasing the duration of action of the drug. Prolonged exposure to fluoxetine changes the expression of genes involved in myelination, a process that shapes brain connectivity and contributes to symptoms of psychiatric disorders. The regulation of genes involved with myelination is partially responsible for the long-term therapeutic benefits of chronic SSRI exposure.
Sources: en.wikipedia.org
== Mechanism of action == The toxin cleaves SNARE proteins, preventing the release of acetylcholine at the neuromuscular junction and producing flaccid paralysis. Botulinum toxin exerts its effect by cleaving key proteins required for nerve activation. First, the toxin binds specifically to presynaptic surface of neurons that use the neurotransmitter acetylcholine. Once bound to the nerve terminal, the neuron takes up the toxin into a vesicle by receptor-mediated endocytosis. As the vesicle moves farther into the cell, it acidifies, activating a portion of the toxin that triggers it to push across the vesicle membrane and into the cell cytoplasm. Botulinum neurotoxins recognize distinct classes of receptors simultaneously (gangliosides, synaptotagmin and SV2). Once inside the cytoplasm, the toxin cleaves SNARE proteins (proteins that mediate vesicle fusion, with their target membrane bound compartments) meaning that the acetylcholine vesicles cannot bind to the intracellular cell membrane, preventing the cell from releasing vesicles of neurotransmitter. This stops nerve signaling, leading to flaccid paralysis. The toxin itself is released from the bacterium as a single chain, then becomes activated when cleaved by its own proteases. The active form consists of a two-chain protein composed of a 100-kDa heavy chain polypeptide joined via disulfide bond to a 50-kDa light chain polypeptide.
The death penalty response by Shanmugam during the BBC interview was well-received and supported by many members of the public on social media, who also voiced their support for capital punishment for drugs in Singapore. In light of the execution of Abdul Rahim Shapiee (and his accomplice), Pritam Singh, opposition leader of Parliament and chairman of Workers' Party, wrote to Singapore newspaper Today to express his support for the death penalty for drug crimes in Singapore and the execution of drug traffickers. Singh nonetheless argued that there should be changes made to rectify the shortcomings in determining the extent of one's cooperation with the authorities during investigations before sentencing, citing cases of traffickers receiving death sentences before courts decided they were couriers and could sentence them for life, as well as cases like Abdul Rahim's, who was sentenced to death despite being a courier and having provided substantive assistance. Singh also expressed concern about the need to curb the frequent abuse of court processes by drug traffickers and their lawyers. The Ministry of Home Affairs (MHA) revealed that from 2013 to early 2022, certificates of substantive assistance were issued to 82 out of 104 drug traffickers regardless of nationality, while there were 14 out of the remaining 22 sentenced to death and the other eight traffickers sentenced to life imprisonment due to mental illnesses.
=== Karyotyping === The routine chromosome analysis (Karyotyping) refers to analysis of metaphase chromosomes which have been banded using trypsin followed by Giemsa, Leishmanns, or a mixture of the two. This creates unique banding patterns on the chromosomes. The molecular mechanism and reason for these patterns are unknown, although it's likely related to replication timing and chromatin packing. Several chromosome-banding techniques are used in cytogenetics laboratories. Quinacrine banding (Q-banding) was the first staining method used to produce specific banding patterns. This method requires a fluorescence microscope and is no longer as widely used as Giemsa banding (G-banding). Reverse banding, or R-banding, requires heat treatment and reverses the usual black-and-white pattern that is seen in G-bands and Q-bands. This method is particularly helpful for staining the distal ends of chromosomes. Other staining techniques include C-banding and nucleolar organizing region stains (NOR stains). These latter methods specifically stain certain portions of the chromosome. C-banding stains the constitutive heterochromatin, which usually lies near the centromere, and NOR staining highlights the satellites and stalks of acrocentric chromosomes. High-resolution banding involves the staining of chromosomes during prophase or early metaphase (prometaphase), before they reach maximal condensation.
== Society and culture == Ethylmorphine was first marketed in France in 1953 by Houde, and in Norway and Spain in 1960. It is not marketed in the United States and is a Schedule II controlled substance.
A large number of benzodiazepine derivatives have been synthesised and their structure-activity relationships explored in detail. This chart contains binding data for benzodiazepines and related drugs investigated by Roche up to the late 1990s (though in some cases the compounds were originally synthesised by other companies such as Takeda or Upjohn). Other benzodiazepines are also listed for comparison purposes, but it does not however include binding data for;
Sources: en.wikipedia.org
== Properties == Umami has a mild but lasting aftertaste associated with salivation and a sensation of furriness on the tongue, stimulating the throat, the roof and the back of the mouth. By itself, umami is not palatable, but it makes a great variety of foods pleasant, especially in the presence of a matching aroma. Like other basic tastes, umami is pleasant only within a relatively narrow concentration range. The optimum umami taste also depends on the amount of salt, and at the same time, low-salt foods can maintain a satisfactory taste with the appropriate amount of umami. One study showed that ratings of pleasantness, taste intensity, and ideal saltiness of low-salt soups were greater when the soup contained umami, whereas low-salt soups without umami were less pleasant. Another study demonstrated that using fish sauce as a source of umami could reduce the need for salt by 10–25% to flavor such foods as chicken broth, tomato sauce, or coconut curry while maintaining overall taste intensity. Some population groups, such as the elderly, may benefit from umami taste because their taste and smell sensitivity may be impaired by age and medication. The loss of taste and smell can contribute to poor nutrition, increasing their risk of disease. Some evidence exists to show umami not only stimulates appetite, but also may contribute to satiety.
In early 2022 a promotional video was shot with influencer Niko Omilana showing a chicken farm in the KFC supply chain. The video depicted birds with a good quality of life. Animal rights activists, working on behalf of the vegan food brand VFC, entered the same farm months later and allegedly found vastly different conditions, with instances of "severe overcrowding" and "lame and dead birds". A spokesperson for the Moy Park meat company who operated the farm said: "Claims such as these are treated incredibly seriously and we immediately reviewed the footage along with independent audits and veterinary reports. This farm is managed to a very high standard and our preliminary findings show that it is meeting those standards." On November 9, 2022, KFC Germany issued an announcement inviting its German audience to celebrate Kristallnacht with "Cheesy Chicken". An apology was issued shortly afterwards, blaming the original message as an "error in our system". In May 2024, the closure of the outlet in Malaysia was reported due to the ongoing Israeli–Palestinian conflict. Attacks on two outlets in Baghdad, Iraq were also reported. In September 2024, KFC announced that it would not meet the Better Chicken Commitment, an animal welfare pledge made in 2019. The commitment includes several welfare standards, such as adopting slower-growing breeds by 2026, but as of 2024, only 1% of KFC's chickens were from such breeds.
This list of former RAF stations includes most of the stations, airfields and administrative headquarters previously used by the Royal Air Force. They are listed under any former county or country name which was appropriate for the duration of operation. During 1991, the RAF had several Military Emergency Diversion Aerodrome (MEDA) airfields: RAF Kinloss, Leeming, Valley, Waddington, Wattisham & Lyneham ended their role from 1 March 1991, leaving Brize Norton, Manston, Leuchars and St Mawgan with the role.
Binding sites can be characterized also by their structural features. Single-chain sites (of "monodesmic" ligands, μόνος: single, δεσμός: binding) are formed by a single protein chain, while multi-chain sites (of "polydesmic" ligands, πολοί: many) are frequent in protein complexes, and are formed by ligands that bind more than one protein chain, typically in or near protein interfaces. Recent research shows that binding site structure has profound consequences for the biology of protein complexes (evolution of function, allostery).
Sources: en.wikipedia.org
HPLC testing separates and quantifies components in a liquid sample. It is used to check identity, purity, concentration, or stability. The technique works best for compounds that dissolve and are not easily vaporized.
The pump maintains a steady flow rate and pressure, which keeps retention times reproducible. Pulsation or flow errors can shift peaks and distort quantitation. Modern pumps use feedback control to reduce these variations.
HPLC alone usually separates compounds but does not always identify them. Retention time matching with a known standard provides tentative identification. Coupling HPLC to mass spectrometry adds mass information that supports structural identification.
System suitability is a set of checks performed before and during a run to confirm that the instrument, column, and method work as expected. Common checks include resolution, tailing factor, theoretical plates, and relative standard deviation of replicate injections. Failure triggers troubleshooting or method adjustment.